- FMA
- The Fabricator
- FABTECH
- Canadian Metalworking
Categories
- Additive Manufacturing
- Aluminum Welding
- Arc Welding
- Assembly and Joining
- Automation and Robotics
- Bending and Forming
- Consumables
- Cutting and Weld Prep
- Electric Vehicles
- En Español
- Finishing
- Hydroforming
- Laser Cutting
- Laser Welding
- Machining
- Manufacturing Software
- Materials Handling
- Metals/Materials
- Oxyfuel Cutting
- Plasma Cutting
- Power Tools
- Punching and Other Holemaking
- Roll Forming
- Safety
- Sawing
- Shearing
- Shop Management
- Testing and Measuring
- Tube and Pipe Fabrication
- Tube and Pipe Production
- Waterjet Cutting
Industry Directory
Webcasts
Podcasts
FAB 40
Advertise
Subscribe
Account Login
Search
Pulsed MIG welding settings for trim
- By Paul Cameron
- Updated February 1, 2024
- October 1, 2014
- Article
- Arc Welding
Q: We use the pulsed-spray-transfer GMAW process in our shop. When setting weld voltage, we can adjust the trim between 0.5 and 1.5. What do those numbers mean, and how do they relate to weld voltage?
Corey G.
A: Pulsed-spray-transfer welding equipment has challenged the conventional wisdom we’ve picked up over the years from using a good old constant-voltage (CV) GMAW machine. With typical CV equipment, you select a voltage and wire feed speed (WFS) combination, possibly a percentage of slope, and inductance.
Most GMAW-P machines run on preset programs. You select the type of wire, the wire diameter, possibly a base material, and the shielding gas. Using this information, the equipment looks at the WFS and calculates the optimal weld voltage. Of course, this voltage may need some type of adjustment depending on what you need.
Settings to Use for Pulsed MIG Welding
For example, the best voltage to lay a 3/8-inch fillet weld at 475 IPM in the flat position (1F) may not be the best voltage for laying a root pass in a horizontal groove (2G) at the same WFS. With this in mind, power source manufacturers have built in a voltage adjustment feature. Think of it as a percentage of optimal voltage.
Some power sources may give you a 0.50 to 1.50 range, while others a 0 to 50 range. This adjustment range is the trim. Using the 0.50 to 1.50 range as an example, 1.00 is considered the optimal setting. When you reduce your trim from 1.00 to 0.85, you have reduced arc length and, in doing so, reduced weld voltage. Similarly, when you increase trim to 1.15, you’ve increased arc length and therefore increased weld voltage.
This is similar to what you were doing all along on that old CV GMAW equipment. When you reduced voltage, you were reducing arc length. Even with this new fancy equipment, the age-old understanding that weld voltage has a direct relationship to arc length still applies.
What’s different is that a trim of 1.00 for a given electrode will give you a completely different weld voltage when you change electrode, shielding gas, or WFS. Most of today’s pulsed equipment will display average weld voltage as the equipment is welding, and some will continue to display it for a short period (seconds) after you’ve stopped welding. This feature helps you to monitor compliance to the weld procedure specification (WPS).
About the Author
Paul Cameron
Braun Intertec
4210 Highway 14 East
Rochester, MN 55904
About the Publication
subscribe now
The Welder, formerly known as Practical Welding Today, is a showcase of the real people who make the products we use and work with every day. This magazine has served the welding community in North America well for more than 20 years.
start your free subscription- Stay connected from anywhere
Easily access valuable industry resources now with full access to the digital edition of The Fabricator.
Easily access valuable industry resources now with full access to the digital edition of The Welder.
Easily access valuable industry resources now with full access to the digital edition of The Tube and Pipe Journal.
Easily access valuable industry resources now with full access to the digital edition of The Fabricator en Español.
- Podcasting
- Podcast:
- The Fabricator Podcast
- Published:
- 04/30/2024
- Running Time:
- 53:00
Seth Feldman of Iowa-based Wertzbaugher Services joins The Fabricator Podcast to offer his take as a Gen Zer...
- Trending Articles
Aluminum MIG wires offer smooth feeding, reduced tangling
The role of flux in submerged arc welding performance
Three ESAB welding machines win Red Dot Awards for product design
Power source added to cobot welding system for simplified automation
Connecticut students compete in Maritime Welding Competition
- Industry Events
Pipe and Tube Conference
- May 21 - 22, 2024
- Omaha, NE
World-Class Roll Forming Workshop
- June 5 - 6, 2024
- Louisville, KY
Advanced Laser Application Workshop
- June 25 - 27, 2024
- Novi, MI
Precision Press Brake Certificate Course
- July 31 - August 1, 2024
- Elgin,