- FMA
- The Fabricator
- FABTECH
- Canadian Metalworking
Categories
- Additive Manufacturing
- Aluminum Welding
- Arc Welding
- Assembly and Joining
- Automation and Robotics
- Bending and Forming
- Consumables
- Cutting and Weld Prep
- Electric Vehicles
- En Español
- Finishing
- Hydroforming
- Laser Cutting
- Laser Welding
- Machining
- Manufacturing Software
- Materials Handling
- Metals/Materials
- Oxyfuel Cutting
- Plasma Cutting
- Power Tools
- Punching and Other Holemaking
- Roll Forming
- Safety
- Sawing
- Shearing
- Shop Management
- Testing and Measuring
- Tube and Pipe Fabrication
- Tube and Pipe Production
- Waterjet Cutting
Industry Directory
Webcasts
Podcasts
FAB 40
Advertise
Subscribe
Account Login
Search
Achieving a good work lead connection
- By Paul Cameron
- Updated February 29, 2024
- August 29, 2014
- Article
- Arc Welding
Q: What makes a good ground connection, and why is it important?
Proper Work Lead Setup
A: In a welding circuit, current needs to pass through as few connections as possible, and the circuit itself needs to be as short as is practical. On the positive (+) side for gas metal arc welding (GMAW), direct-current electrode positive (DCEP) passes through the (+) stud connection, the feeder connection, the gun connection, and the contact tip (to the wire) connection. With the exception of the wire, all of those connections are typically copper or brass. On the negative (-) side, current should pass through the (-) stud connection, the cable to the work lead (ground) clamp, possibly across a rotating surface, and then to the workpiece.
Poor Work Lead Connections
When any of these connections are anything less than clean copper, brass, or aluminum to clean copper, brass, or aluminum, the possibility of a poor connection and a current or voltage loss exists. These losses can be great enough to run outside the parameters of the weld procedure, causing spatter or a lack of fusion. That can get a welder into trouble.
Here are some good examples of poor connections:
- A work lead connected to a building column.
- A steel building column and a steel bolt—this connection will rust and create resistance.
- A work lead connected to a steel plate and run across the floor. Of course, the initial connection is the same as the building column. When that steel plate isn't of a sufficient size and that plate is joined by one or several welds, the conditions are ripe for a drop in current and/or voltage.
The two conditions mentioned above also create a safety hazard. Once a work lead contacts a building, it gives current alternate routes. One of the most popular is through a jib or bridge crane. Aside from creating havoc with the crane’s electrical system, current passes through the lifting devices such as the cables, hooks, and chains, heating them over and over, thus weakening them and making them susceptible to failure.
One last good example of a poor connection is an unlubricated rotary clamp, or a rotary clamp with a lubricant that is not made for electrical connections.
Bottom line, the best work lead connection is the one that runs from the stud on the machine to the workpiece close to the welding being done and at the shortest distance and with the least amount of connections in it. A key to quality welding starts with a good-quality circuit, and a key component of that circuit is the condition of the work lead.
Note: I’ve replaced the word ground with work lead. You should also make that change in your daily welding dialogue. Keep in mind, a welding ground doesn’t ground anything.
About the Author
Paul Cameron
Braun Intertec
4210 Highway 14 East
Rochester, MN 55904
About the Publication
subscribe now
The Welder, formerly known as Practical Welding Today, is a showcase of the real people who make the products we use and work with every day. This magazine has served the welding community in North America well for more than 20 years.
start your free subscription- Stay connected from anywhere
Easily access valuable industry resources now with full access to the digital edition of The Fabricator.
Easily access valuable industry resources now with full access to the digital edition of The Welder.
Easily access valuable industry resources now with full access to the digital edition of The Tube and Pipe Journal.
Easily access valuable industry resources now with full access to the digital edition of The Fabricator en Español.
- Podcasting
- Podcast:
- The Fabricator Podcast
- Published:
- 04/30/2024
- Running Time:
- 53:00
Seth Feldman of Iowa-based Wertzbaugher Services joins The Fabricator Podcast to offer his take as a Gen Zer...
- Trending Articles
Aluminum MIG wires offer smooth feeding, reduced tangling
The role of flux in submerged arc welding performance
Three ESAB welding machines win Red Dot Awards for product design
Power source added to cobot welding system for simplified automation
Connecticut students compete in Maritime Welding Competition
- Industry Events
Pipe and Tube Conference
- May 21 - 22, 2024
- Omaha, NE
World-Class Roll Forming Workshop
- June 5 - 6, 2024
- Louisville, KY
Advanced Laser Application Workshop
- June 25 - 27, 2024
- Novi, MI
Precision Press Brake Certificate Course
- July 31 - August 1, 2024
- Elgin,